How to Make a Wood Sign with a Custom Quote and Wood Frame

It's easy to make your own wood signs with quotes or personalized messages. You can make the signs with wood frames with minimal tools - no fancy equipment needed!

Putting the finishing touches on our kitchen has been on my to-do list for the past three years.  We gutted the kitchen, installed new hardwood floors, cabinets, appliances and half of the wainscoting, and then I stopped.  Everything was livable and looked good enough, so I let it sit in a 90% finished state for way too long.  I’m finally finishing up the room, and I started with our eat-in dining area.

I’ve been wanting to try to make my own wood signs and love this verse from Acts, so it seemed like the perfect fit for above our table.  I’ll show you how to make a sign with a wood frame; you won’t believe easy it actually is and how few tools you actually need!

Supplies You’ll Need

  • 1/4″ sanded plywood, cut down to the size you’d like to make your sign
  • 1″ x 2″ boards (see note below)
  • 1″ and 1.5″ trim nails
  • hammer (or you can use an air nailer, if you have it)
  • stain and/or paint
  • paint
  • paint pen
  • computer and printer

You’ll start by making the base of your sign.  I know the employees at Home Depot will cut down pieces of plywood to the exact size you’d like, or they also sell smaller pieces (I’ve seen 24″ x 24″ or 48″ x 24″)  Recently, I’ve noticed that craft stores are carrying 1/4″ plywood panels as well.  Maybe they always have, but I didn’t seen to notice until recently.  Either way, you really don’t need any extra tools for this step!

how to build a wood sign with wood frame

In order to be able to nail the wood frame into the panel, you’ll need to add a little extra to the back.  Nailing into the thin sides of 1/4″ plywood is not easy, nor is it very sturdy.  I used two 1x2s that I cut down to the same length as the longer side of the plywood.  Again, the folks at your home improvement store can cut them down for you, or a simple saw will cut through them easily.  Then, nail (with 1″ nails) those two boards to the back of the panel, by nailing through the front of the plywood panel.  You can use wood filler to fill in the holes, if you’d like.

At this point it’s best to paint or stain the plywood.  I just painted mine with two coats of flat white latex paint.

While the paint is drying, you can set up the lettering or quote for your sign.  I used a free, online program called PicMonkey to design the verse.  PicMonkey has a lot of fonts that are free to use for personal use, so if you are planning on making a sign to hang in your home, have fun designing with all the fonts!  If you plan to sell any of your signs, you’ll need to purchase fonts with a commercial license.

Here is a complete tutorial on using PicMonkey to design lettering for signs!

Click on the image to sign up!
Click on the image to sign up!

*Update – I created a graphics library with many of the images and lettering I’ve used in DIY project, including this verse!  You can click on the image above to sign up and gain access to all of those files!

how to make a sign with a quote and wood frame

After the paint or stain dries and you paint on the lettering, you can attach the wood frame.  You’ll need four 1x2s cut to two different lengths.  I honestly just laid my plywood on the ground and then measured the height of the board.  I cut those two pieces, set them on the frame, and then measured the length I would need for the top and bottom boards.  Those boards will cover the top and bottom edges of the sides of the frame.

how to build a barnwood sign

Instead of using 1x2s for my frame, I just bought a cedar fence panel and ripped it down to 3/4″ inch thick pieces (the same thickness as a 1×2″ board).  I also chose to add a little color to my frame.  You could stain them in a color of your choice once they are cut.

how to weather wood with stain

I used Weatherwood Stain; an awesome product that naturally weathers wood.  It brought out the knots and veins in the wood just beautifully!

how to make a word sign with wood frame

Once the frame has dried, it’s time to attach it to your panel.

how to make a sign with wood frame

Basically, you will nail each of your frame boards into the 1x2s on the back of your plywood panel.  On the top, you’ll nail every few inches, but on the side boards, you’ll only nail into the end of the 1×2 on the top and the bottom.

how to make a sign with a quote and wood frame

After it’s all put together, it’s ready to hang on the wall!  I used two saw tooth picture hangers on the back, but you could also use d-hangers on each end on the back as well.  Because 1/4″ plywood was used, it’s really not very heavy.

how to make a wood sign with

If you wanted to forego the step of adding a 1×2 to the back of the panel, you could probably just buy 1/2″ plywood.  It should be thick enough to nail the wood frame into, but it will be quite a bit heavier.

It's easy to make your own personalized wood signs by using a free online photo editing program and transferring the image to paint the letters perfectly. All you'll need is a computer and printer!!

Here is a little peek at our eat-in kitchen that is now 98% finished.  Unfortunately, I only finished the trim on the wainscoting in this area, so I still need to finish this in the rest of the kitchen.  It will get done, eventually.

It's easy to make your own wood signs with quotes or personalized messages. You can make the signs with wood frames with minimal tools - no fancy equipment needed!

Here are a few more signs I’ve made for our house and cottage.

Like what you see? I’d love for you to follow along!

Facebook || Pinterest || Instagram || Google + || Bloglovin’

signature

18 thoughts on “How to Make a Wood Sign with a Custom Quote and Wood Frame

  1. Your sign is beautiful! Thanks for sharing how you framed it up to, because that really finished it perfectly.

    Thanks for linking up at Knick of Time – I’m pinning this to the Knick of Time party board, and giving you a shout-out on FB tomorrow! 🙂

  2. Good Morning!! I wanted to stop by and let you know that your post has been selected as a Feature post for the Welcome Home Wednesdays Link Party!! Stop by this morning to see your post linked up and don’t forget to grab your Featured Button too! ~Lisa~

  3. After you designed your quote what did you do in order to paint it on? Did you print it off and just trace it or what?

Leave a Reply

Your email address will not be published. Required fields are marked *

CommentLuv badge